Introduction

...

5. Alter the config.yml and change parameters under path NEED TO BE PROVIDEDpath 

Installing Mode : EALTEdge using Ansible-Playbooks

...

Once the execution is completed in console will see prompt "EALTEdge Environment Installed  , Components Install CENTER and EDGE Nodes Successfully"

...

1. git clone the ealt-edge repo, to download the software to install the EALTEdge Environment.

root@akraino-mec-0002:~# git clone "https://gerrit.akraino.org/r/ealt-edge"

2. go to CLI directory 

root@akraino-mec-0002:~#cd ealt/infra/cli/

root@akraino-mec-0002:~#chmod +x build _cli.sh

root@akraino-mec-0002:~#source build_cli.sh

root@akraino-mec-0002:~#cd ~/ealt-edge/ocd/infra/playbooks

Note: The CLI Commands to setup the environment should be executed only from above path.

3.  Edit the Configuration File : ealt-inventory.ini with the details of MECM and MEC Hosts. 

root@akraino-mec-0002:~#vi ealt-inventory.ini

4. Execute the below command to install EALTEdge Environment 

root@akraino-mec-0002:~#ealt init all 

Above command will install the various component. Refer the below table for detail information. 

Other CLI Commands:

Command to Install only Edge Node

root@akraino-mec-0002:~#ealt init edge

Snapshot Deployment Overview

...

##Now get ca certificate use below command
```
curl http://10.43.130.35:8200/v1/pki/ca/pem
```
##10.43.130.35 is your vault ip, need to replace with latest vault ip

Image Modified

Kong documentation

...

##First create setup by using below command server running in https
```
ansible-playbook ealt-all.yml -i ealt-inventory.ini --extra-vars "operation=install mode=prod"
```
##For http use below command
```
ansible-playbook ealt-all.yml -i ealt-inventory.ini --extra-vars "operation=install mode=dev"
```
##Mep will install as a pod
##MEP services will be running in the MEC Host (MEP)
##Check the mep running or not use below command
```
kubectl get po -n mep
```
##Output -
```
kubectl get svc -n mep
```
##Output -
##Configure Kong
##HTTPS Env - Rest API request Adding Services and Adding Route in Kong API Gateway
```
https://www.ealtedge.org:30012/services
https://www.ealtedge.org:30012/routes
```
##DNS mapping should be done correctly

##HTTPS Env - Rest API request deleting route and services
```
https://www.ealtedge.org:30012/services/http-mp1
https://www.ealtedge.org:30012/routes/mp1
```
##HTTP Env - Rest API request Adding Services and Adding Route in Kong API Gateway
```
http://www.ealtedge.org:30011/services
http://www.ealtedge.org:30011/routes
```
##DNS mapping should be done correctly

##HTTP Env - Rest API request deleting route and services
```
http://www.ealtedge.org:30011/services/http-mp1
http://www.ealtedge.org:30011/routes/mp1
```

##To verify the configurations done in Kong.
##Trigger the below Rest API

##In HTTP mode.
```
http://www.ealtedge.org:30010/mp1/mep/mec_service_mgmt/v1/applications/id123456/services
```
##In HTTPS Mode
```
https://www.ealtedge.org:30011/mp1/mep/mec_service_mgmt/v1/applications/id123456/services
```

##Get certificate from MEP server
##Login MEP server
```
cd /tmp/mepserver/deploy/
```
##Given path you will get all required certificates
```
ca.crt
tls.key
tls.crt
```
##ca.crt client certificate
##tls.key is a server key
##tls.crt server certificate

Troubleshooting

Error Message Guide

...

...

...

...