...
...
...
...
...
...
PLEASE REFER TO R1 NETWORK CLOUD RELEASE DOCUMENTATION
NC Family Documentation - Release 1
THIS DOCUMENTATION WILL BE ARCHIVED
This guide instructs how to build and install an Akraino Edge Stack (AES) Regional Controller node.
...
| Code Block | ||
|---|---|---|
| ||
# host name for server SRV_NAME=aknode44 # server oem - Dell or HPE (case sensitive) SRV_OEM=Dell # out of band interface information for server (idrac/ilo/etc) SRV_OOB_IP=192.168.41.44 SRV_OOB_USR=root SRV_OOB_PWD=ROOT_PASSWORD # mac address of server to be used during the build - not required for Dell servers # SRV_MAC=3c:fd:fe:b8:10:60 # namethe of network interface used during build when ipxe.efi is booted and when os is booted # ipxe numbers ports from 0-n in pci bus order. # the netx value will depend on how many nics are in the server # and which pci device number is assigned to the slot SRV_IPXE_INF=net8 # the build interface is the nic used by the Ubuntu installed to load the OS SRV_BLD_INF=enp135s0f0 # the boot boot device is the device name on which the OS will be loaded SRV_BOOT_DEVICE=sdg # ipxe script to use - based on the os version and kernel to install # valid options are script-hwe-16.04.5-amd64.ipxe or script-16.04.5-amd64.ipxe SRV_BLD_SCRIPT=script-hwe-16.04.5-amd64.ipxe # template xml file to set bios and raid configuration settings SRV_BIOS_TEMPLATE=dell_r740_g14_uefi_base.xml.template SRV_BOOT_TEMPLATE=dell_r740_g14_uefi_httpboot.xml.template SRV_HTTP_BOOT_DEV=NIC.Slot.7-1-1 # VLAN to use during build and for final network configuration SRV_VLAN=41 # basic network information for dhcp config and final server network settings SRV_MTU=9000 SRV_IP=192.168.2.44 #Note: This address is the same as the 'TARGET_SERVER_IP' defined below and in the akrainorc file# SRV_SUBNET=192.168.2.0 SRV_NETMASK=255.255.255.0 SRV_GATEWAY=192.168.2.200 SRV_DNS=192.168.2.85 SRV_DOMAIN=lab.akraino.org SRV_DNSSEARCH=lab.akraino.org SRV_NTP=ntp.ubuntu.org # root password for server being built SRV_PWD=SERVER_PASSWORD # network bond information SRV_BOND=bond0 SRV_SLAVE1=enp135s0f0 SRV_SLAVE2=enp135s0f1 |
...
| Warning | ||
|---|---|---|
| ||
The Regional Controller installation is not idempotent at this time. If errors are encountered during this phase, it is recommended that the errors be triaged and resolved, followed by an Operating System re-installation. This will ensure a "clean slate" Bare Metal Server before trying again. |
A successful installation will end as follows. Note that any time estimates (e.g., "This step could take up to 15 minutes") and elapsed times are likely inaccurate.
...
The Regional Controller Node installation is now complete.
Please note: the rsa keys generated by the installation located at /root/.ssh/id_rsa.pub It will be necessary to generate rsa keys on the RC which must be copied and inserted into the 'genesis_ssh_public_key' attribute in site input yaml file used when subsequently deploying each Unicycle pod at any edge site controlled by the newly built RC.
...