Versions Compared

Old Version 37

changes.mady.by.user yu marvin

Saved on

compared with

New Version 38

changes.mady.by.user yu marvin

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Table of Contents
OpenNESS 19.12 Design

...

Microservices of Openness Infrastructure mode DescriptionDeployment methodDeployment of the componentPropose to integrate
eaaapplication/service registration, authentication etcdeploymentedge nodeyes
edgednsfor client to access microservices in edge nodedaemonset (propose to change to deployment)edge nodeyes
interfaceservicesimilar with providernet implemented in ovn4nfv-k8s-plugindaemonsetedge nodeno, will use ovn4nfv-k8s-plugin's provider network
cnca

Core Network Configuration: Configure the access network (e.g., LTE/CUPS, 5G) control plane

deploymentcontrollerno
sysloglog service for opennessdaemonsetcontroller & edge nodeno
multusenabling attaching multiple network interfaces to podsdaemonsetcontroller & edge nodeAlready covered by ONAP4K8s - KUD
nfdnode feature discoverydaemonsetcontroller & edge nodeAlready covered by ONAP4K8s - KUD
sriovsriov network device plugin & sriov cnidaemonsetcontroller & edge nodeAlready covered by ONAP4K8s - KUD
topology managerkubernetes topology managerKubelet componentcontroller & edge nodeWork in Progress to upgrade the K8s v16.0 integrate into ONAP4K8s - KUD
CMKCPU Managerpart of kubeletcontroller & edge nodeWork in Progress - Integrate into ONAP4K8s - KUD
biosUsed for change BIOS and firmware configuration: CPU configuration, Cache and Memory configuration, PCIe Configuration, Power and Performance configuration, etcprivileged Podcontroller & edge nodeRequired for ICN? Already in ICN Metal3, could be enabled part of it
fpgaOpen Programmable Acceleration Engine (OPAE) package consisting of a kernel driver and user space FPGA utils package that enables programming of the FPGA is used. sriov is used to configure the FPGA resources such as Virtual Functions and queuespodcontroller & edge nodeNeed to integrate into ONAP4K8s - KUD with FPGA device

...

Microservice

Test cases in KUD

Test cases to be addadded

Multus

  1. Enable Multus AddOn support.
  2. Verify the minion interface network type
    • bridge[1]
    • ovn4nfv[2]

[1]https://github.com/onap/multicloud-k8s/blob/9c63ce2a7b2b66b3e3fce5d1f553f327148df83f/kud/tests/_common.sh#L856
[2]https://github.com/onap/multicloud-k8s/blob/9c63ce2a7b2b66b3e3fce5d1f553f327148df83f/kud/tests/_common.sh#L1053

  • Enable Multus AddOn support.
  • Verify the minion interface network type
  • bridge
    • ovn4nfv

    1. Add more cni-network type verification:
      • macvlan
      • ipvlan
      • ptp
      • vlan

    SR-IOV CNI

    1. Enable SR-IOV cni and network device plugin AddOn support.
    2. Check VF allocated status
      • Verify single VF allocated
    3. Enable SR-IOV cni and network device plugin AddOn support.
    4. Check VF allocated status
      • Verify single VF allocated
    1. Add multi-VF allocated verification
      • Verify multiple VF allocated

    SR-IOV  Network Device Plugin

    NFD

    1. Enable NFD AddOn support.
    2. Using the "affinity"[1] field verifies If NFD is effective or not.



    [1]https://github.com/onap/multicloud-k8s/blob/master/kud/tests/nfd.sh#L27

    Enable NFD AddOn support.

    1. Using the "affinity" field verifies If NFD is effective or not.
    2. Enhance the "affinity" verification method.
      • Add different kinds of operator, e.g. In, NotIn, Exists, DoesNotExist,Gt,   Lt.
    3. Add a “nodeSelector” field to verify.

    CMK

    nil

    It's going to be added the patch below:

    https://gerrit.onap.org/r/c/multicloud/k8s/+/102311

    ...